Alat Pendeteksi dan Notifikasi Kerusakan pada Gardu Distribusi PLN

  • Muhammad Irmansyah Politeknik Negeri Padang
  • Yul Antonisfia Politeknik Negeri Padang
  • Amril Amril Politeknik Negeri Padang
  • Era Madona Politeknik Negeri Padang
  • Zhefry Anovra Politeknik Negeri Padang

Abstract

PLN distribution transformer is a transformer as a voltage-lowering from medium to low voltage which will distribute to customers. In some cases, officers are usually constrained by unpredictable disturbances, especially in power distribution networks to customers which disturbed suddenly and on the distribution station itself which caused the supply of power from the main station are not distributed to area or customers are not supply electrically. In this research is designed a device to improve the officers performance in maintenance and repaired on the network. This device use to detect and give notification of information damage on the FCO (Fuse Cut Out) distribution station based microcontroller through sms. This tool is intended to lighten the duty of PLN officers. This tool is installed inside the distribution station transformer. This system operates if the sensor detects the network outages or damage or trips on one of the distribution station transformer along the network. Due to the position of the tool installed on the end of distribution station, so the tool can detect the interference or damage occurs along the network. The tool will send the information data to the officer via sms.         

References

[1] http://elektroteknik-unm.blogspot.co.id/2013/10/gardu-trafo-tiang.html
[2 http://ajinurmawan45.blogspot.co.id/2015/02/pengertian-fco-fuse-cut-out.html
[3] http://dunialistrikelektron.blogspot.co.id/2015/04/prinsip-kerja-fuse-cut-out-fco.html
[4] https://inrasta.blogspot.co.id/2017/01/materi-fuse-cut-out-fco.html
[5] https://plnrayonbinjaikota.wordpress.com/2017/02/10/sop-pemeliharaan-fuse-cut-out-fco/
[6] Fitriandi Afrizal, 2016,“Rancang Bangun Alat Monitoring Arus dan Tegangan Berbasis Mikrokontroller dengan SMS Gateway”, ELECTRICIAN-Jurnal Rekayasa dan Teknologi Elektro.
[7] Fakarilmi Hadi, 2015,“Perancangan dan Implementasi Sistim Kontrol dan Monitoring KWH Meter Digital Mengggunakan SMS Gateway”, e-Proceding of Engineering:Vol.2 Agustus 2015/page 2555
[8] Safii Muhammad, 2018,“Perancangan Sistim Monitoring Tegangan Output Genset Menggunakan Ethernet Shield & SMS Gateway Berbasis Arduino Uno”, METIK Jurnal Vol.2. No.2 tahun 2018/page 46
[9] Iqbal Gilang, 2016, “Sistim Monitoring Proses Charging Lampu Penerangan Jalan Umum Berbasis SMS Gateway”, Tugas Akhir, Universitas Jember.
[10]http:// kursuselektronikaku.blogspot.com/2018/01/Membuat Alat Monitor Tegangan dan Arus AC Menggunakan Arduino UNO dan notifikasi via SMS Gateway
[11]http://klinikrobot.com/product/electrical-sensor/zmpt101b-single-phase-ac-voltage-sensor.html
[12]http://Saptaji.com/2015/8/Cara mengirim SMS dengan SIM800 dan Arduino
[13] http://stackoverflow.com/questions/44839087/how-to-send-sms-with-gsm-modul-sim800-andarduino-uno
[14]http://nofgipistonwordpress.com//2017/11/25/Membuat Alarm Kebocoran Gas LPG via SMS Menggunkan Arduino dan SIM800L
[15]Ketut Resika Arthana, 2017,“Perancangan Alat Pendeteksi Detak Jantung Dan Notifikasi Melalui SMS”, Seminar Nasional Riset Inovatif.
Published
2018-09-08
How to Cite
IRMANSYAH, Muhammad et al. Alat Pendeteksi dan Notifikasi Kerusakan pada Gardu Distribusi PLN. Prosiding SISFOTEK, [S.l.], v. 2, n. 1, p. 213 - 216, sep. 2018. ISSN 2597-3584. Available at: <http://seminar.iaii.or.id/index.php/SISFOTEK/article/view/80>. Date accessed: 20 oct. 2019.
Section
5. Teknologi & Komputer